NEW PRODUCTS

October 2009 Cable Chute Line Carriers

The Most Effective Line Carriers

Condux Cable Chute Line Carriers are designed to pass through conduit without damaging the conduit or existing cable. To use a Cable Chute Line Carrier you would tie a line or webbing to a Chute, insert the Chute into the Conduit or duct, and blow compressed air propelling the Chute to the end of the duct.

All Cable Chute Line Carriers are made with the highest quality fabrics and attention to detail. All products are hand made and go through a series of quality checks prior to being shipped out.

Advantages of using Cable Chute Line Carriers over other carriers:

• No damage to cable or conduit
• Eliminates need for duct rodding
• Durable and flexible
• Quick and easy installation
• Cost effective

October 2009 WDR505 Remote Control Kit

The Condux WDR505 Remote Control Kit allows the user to operate the WDR505 from up to 25 feet away. The WDR505 Remote Control Kit allows the user to pay out and pull back winchline rope and also provides an emergency stop control for safety purposes.

Factory Installation Only.

October 2009 Comfit Couplers

Comfit is a unique Hi-Tech coupler for HDPE cable ducts. Leak tested at 230 PSI and resistant to corrosion and most chemicals.

Comfit is designed in accordance with the special demands of the leading cable duct companies and contractors.

Comfit is excellent for both blowing and pulling methods.

Comfit has a compact profile reducing difficulties traditionally encountered in manholes, narrow trenches and plowing machines.

Comfit’s push-fit method ensures fast and simple assembly and disassembly. Push the duct ends into the coupler for a locked and air sealed assembly. No special tools are needed.

October 2009 Chamfering Tool

The Chamfering Tool is designed to bevel the end of the duct to ensure a correct fit with the coupling.

October 2009 Microfit Connectors

MICROFIT is push-fit connectors for blown fiber. Microfit Connectors are an effortless, fast connection for up to 217 PSI blowing. The Microfit range is designed specifically for Fiber To The Home networks.

Microfit features include:

· Resistant to high pressures for blowing cables through guide tubes
· Resistant to corrosion and most chemicals
· Water and air tight
· Suitable for use in a wide range of working temperatures

October 2009 1/2 Inch CTS Gas Pipe Pulleye

Tapered buttress threads thread into the gas pipe for maximum pulling strength. These eyes connect directly to a Condux Break-away Swivel (compatible with Condux 5/8" Break-away Swivel only). When properly sized and installed, these eyes will not pull out of the gas pipe until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the gas pipe manufacturers.

July 2009 GRC to PVC Coupling

The Condux GRC to PVC Coupling is an accessory for the Condux Split Winch Line Blower. Adapt your threaded GRC pipe to PVC so you can use the Condux Winch Line Blower to blow in your hardline, rope or tape.

June 2009 7/8” Break-Away Swivel for Directional Drilling

Avoid overstressing cable or conduit being pulled in during directional drilling operations. The Condux 7/8” Break-Away Swivel for directional drilling is designed exclusively to provide both the swivel and the break link for product pull-back. Eliminate the use of two or more components and shorten the gap between the reamer and pulling eye. No need to use “weak link” pipe sections or wire when using the 7/8” Condux Break-Away Swivel.

May 2009 New Fiber Optic Puller ECB

The new optional Condux Electronic Control System features a large LED Display and Paperless Recorder with trend display. The Paperless Recorder includes: Trend Display, CompactFlash™ card slot with 256MB Flash Card, and a USB interface. A programmable overload set point has both an audible and visual indication of an overload condition. The Electronic Control Box also has the capability to disengage the cable puller if an overload occurs.

May 2009 Fixed Head & Clevis Head Innerduct Pulling Eyes

The new Condux Fixed Head & Clevis Head Innerduct Pulling Eyes feature tapered buttress threads that thread into the innerduct for maximum pulling strength, and also feature a shorter length and better cutting ability. These eyes connect directly to a Condux swivel. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.

May 2009 1.25" Feeding Sheave

The Condux 1.25" Cable Feeding Sheave plugs into 1.25" conduit or innerduct, guiding the cable safely into the conduit or innerduct regardless of the pulling angle.  Replacement Sheaves are also available.